Skip to main content

Deployment Success

Tools and Technologies

3126 Topics
C
choi-yoonsungAdventurer
asked in Installation & Configuration
Unable to Complete Next Authentication for Nutanix Community Edition

I have installed Nutanix Community Edition but cannot complete the Next authentication. I have configured the IP of the CVM and the external IP of the cluster. The CVM can resolve the name of www.nutanix.com. I can log in to my.nutanix.com, portal.nutanix.com, and next.nutanix.com. However, when I enter my email address and click "Get Started" at the following URL, I receive the message below and cannot proceed: "It seems your My Nutanix account is not activated, please go to my.nutanix.com to complete the process" https://www.nutanix.com/products/community-edition/register I have already created an account and can log in freely. Is there anything additional I need to do?

601
C
A
AdamKraitmanWayfarer
asked in Move Application Migration
Migrate from ESXi

I’m running Nutanix CE and need Move to migrate from ESXi—how can I download it without a serial?

831
Exe
B
B.Nel.
asked in Installation & Configuration
Supported upgrade Broadcom VMWare on HPE

Nutanix Compatibility matrix shows that they support the next version of VMWare but there is no 1-click upgrade. I am running on HPE machines and we have been burned in the past where if we use an “off the shelf” ESXi .iso from VMWare it breaks the linkages from VMWare to Nutanix. We can only use an HPE branded (drivers included) VMWare .iso so that the Nutanix tools (vsan and VAAI) work. Broadcom has taken over VMWare they do not supply HPE branded .iso for upgrades according to the Broadcom case I opened. Nutanix does not supply upgrade paths for VMWare according to the Nutanix case I opened. HPE does not integrate with Broadcom anymore according to the HPE case I opened. How do you upgrade your VMWare deployment on a Nutanix linked Prism Central without a full rebuild?

130
B
A
Alexey1001Explorer
asked in Installation & Configuration
hard drive replacement

Good day! Tell me, we previously purchased a Nutanix Lenovo HX5520 cluster - 4 nodes (sn: J304G3WK). Now we need to re-equip this cluster with larger SSD and HDD disksAs it is now:CPU: Intel Xeon Gold 6242 16C ​​150W 2.8GHz Processor - 2 pcs.RAM: 32GB TruDDR4 2933 MHz (2Rx4 1.2V) RDIMM - 12 pcs.SSD: ThinkSystem 3.5" PM883 3.84TB Entry SATA 6Gb Hot Swap SSD - 2 pcs.HDD: ThinkSystem 3.5" 10TB 7.2K SATA 6Gb Hot Swap 512e HDD - 4 pcs. How we want to do it:CPU: Intel Xeon Gold 6242 16C ​​150W 2.8GHz Processor - 2 pcs.RAM: 32GB TruDDR4 2933 MHz (2Rx4 1.2V) RDIMM - 12 pcs.SSD: ThinkSystem 3.5" PM1653 7.68TB Read Intensive SAS 24Gb HS SSD - 4 pcs.HDD: ThinkSystem 3.5" 20TB 7.2K SAS 12Gb Hot Swap 512e HDD - 8 pcs. Will the cluster start with the new disk configuration?

220
A
A
Alexey1001Explorer
asked in Installation & Configuration
Replacing hard drives

Добрый день! Подскажите, у нас были ранее куплен кластер Nutanix Lenovo HX5520 - 4 node (sn: J304G3WK). Сейчас этот кластер нам необходимо переоснастить дисками ssd и hdd большего размера Как есть сейчас: CPU: Intel Xeon Gold 6242 16C 150W 2.8GHz Processor - 2 шт. RAM: 32GB TruDDR4 2933 MHz (2Rx4 1.2V) RDIMM - 12 шт. SSD: ThinkSystem 3.5" PM883 3.84TB Entry SATA 6Gb Hot Swap SSD - 2 шт. HDD: ThinkSystem 3.5" 10TB 7.2K SATA 6Gb Hot Swap 512e HDD - 4 шт Как хотим сделать: CPU: Intel Xeon Gold 6242 16C 150W 2.8GHz Processor - 2 шт. RAM: 32GB TruDDR4 2933 MHz (2Rx4 1.2V) RDIMM - 12 шт. SSD: ThinkSystem 3.5" PM1653 7.68TB Read Intensive SAS 24Gb HS SSD - 4 шт HDD: ThinkSystem 3.5" 20TB 7.2K SAS 12Gb Hot Swap 512e HDD - 8 шт. Запуститься ли кластер с новой конфигурацией дисков?

140
A
D
DaudiVoyager
asked in Installation & Configuration
VMs on same VLAN unreachable.

Hi new here, I have set up a one node cluster following the Nutanix university videos. I added a subnet with vlan 500 on the the vs0 and installed 2 VMs and connected both to the same subnet however I can not reach any but can reach the CVM & host would there be a step am missing?

894
JeroenTielen
H
HeadQuakerVoyager
asked in Installation & Configuration
CPU frequencies in AHV vs in VM

Hello, We have recently set up a new Nutanix infrastructure consisting of two clusters, each with three AHV nodes. The hardware comprises ThinkAgile HX650 V3 CN servers, equipped with Intel(R) Xeon(R) Silver 4416+ CPUs (2GHz, up to 3.9GHz). The BIOS of the AHVs is configured to Performance Schedutil. Our concern is that the VMs are operating at a CPU frequency of 2GHz. Monitoring shows that the CPU frequency never exceeds 2GHz, while the AHV CPUs average around 2.8GHz. Is this behavior a bug, or is it by design? Is there a way to change and increase the CPU frequencies used by the VMs? We are still learning about the Nutanix infrastructure and would appreciate your assistance. Thank you.

724
A
G
ghghcExplorer
asked in Installation & Configuration
Uplink recognition issue on a specific server after initial installation

I have a question. I installed AHV on three servers and successfully configured a cluster. I left the network settings as default during the installation. However, after the setup, when I check the Network Configuration, I notice that on one of the servers, all uplink ports are missing. The strange part is that this doesn’t always happen on the same server — it randomly affects one of the three servers. On the affected server, all uplink ports are shown as disconnected. So I try to configure the bond again by selecting the disconnected uplink ports. When I do this, the server enters maintenance mode and starts a rolling upgrade process, but it never completes — it just stays stuck in a pending state. I checked the server’s BIOS settings, and everything looks normal there. What could be causing this issue?

140
G
apiwat_sang
apiwat_sangAdventurer
asked in Move Application Migration
Request for VDDK 6.0.3 for Nutanix Move

Hello everyone, I am currently facing an issue and need assistance. I am unable to locate and download VDDK 6.0.3, which is required for Nutanix Move to Upload and migrate VMs from vSphere ESXi 5.1. I have already checked the VMware (Broadcom) website, but the minimum version available for download is VDDK 6.7. If anyone has the VDDK 6.0.3 file saved or knows an alternative source for obtaining it, I would greatly appreciate it if you could share it with me.

4615
A
E
eoduettWayfarer
asked in Installation & Configuration
hw compability - avh

Hi can these compatibility errors: cause this error: or is this 2 separated issues? where the system/server is not recognized? and if so, i have tried to find a list of supported hdd of the same size, 600gb everything is working, except that i cant upgrade ahv

160
E
J
johnBJExplorer
asked in Installation & Configuration
Prism Central deployement fail

When I go to PrismCentral registration and enter configuration items => deploy, the following message is detected and it will not deploy.~~~~Prism Element is not compatible to enable Microservice Infrastructure: domain name resolution foprism-central.cluster.local failed the domain name resolution is okay , juste DNS server respond =10; How can w e ta ckl e this problem? ~~~~

770
J
N
niclasskovAdventurer
asked in Installation & Configuration
Can't enable NFS, even after updating to the newest version.

Hello! I’m unable to enable FNS on my test CE nutanix cluster, even after updating both Element and Central to the newest version using LCM. If anyone have any clue of what I’ve done wrong, it would be much appreciated.

492
N
N
niclasskovAdventurer
asked in Installation & Configuration
Is Network Controller supported on Community Editon 2.1?

Hello, just finished installing a new CE 2.1 cluster to experiment a bit, and a new Prism Central. Trying to enable Network Controller, but it says my cluster is not supported. Is this not a feature supported by CE? Or would I have to use a different Prism Central version?

353
N
N
niclasskovAdventurer
asked in Installation & Configuration
Community Edition, can't reach CVM's when trying to segment backplane LAN

Hi! I’m trying to segment, the backplane LAN on an already existing cluster, it passes the validation, but then I get this error when it gets to about 45% Anyone know what i’m doing wrong?I’m following this documentation Link My CVM’s use 10.10.10.11,21,31 And AHV use 10.10.10.10,20,30 Trying to get the backplane to use a 10.10.11.0/24 on a different physical switch. All ports are VLAN tagged with VLAN11 just like the This is the error I get When looking in the Foundation logs, they fail to ping eachother, but I don’t know what the issue there could be, they are using the correct IP’s and the interfaces are up on both sides.

476
N
T
ttenglingTrailblazer
asked in Installation & Configuration
Can Foundation create clusters in VMware Workstation?

In my struggle to find some environment to practice/test Nutanix admin stuff, I’ve now come to Nutanix Foundation (NCE 2.0 worked but is old, NCE 2.1 failed on some networking issue in my environment). Is it possible to create a small single node cluster running as a VM in VMware Workstation using for example Foundation? I made a few tries but it seemed Foundation required IPMI access to the host, but VMs in VMware don’t have IPMI (to my knowledge). It thought maybe a new VM could be recognized by Foundation (tried both the Windows version and the VM) if it had booted DiscoveryOS, but I couldn’t find the Discovery OS image anywhere… Is there a way forward for an installation like this or is it a dead end?

583
JeroenTielen
M
MikeLeoneAdventurer
asked in Move Application Migration
VM resolution stuck at 1280x1024 after MOVE from ESXi to AHV

We are starting to migrate from ESXi to AHV, using the MOVE application. And as the title says, all the VMs are stuck on 1280x1024 resolution when they come up on AHV. I’ve tried the “Preferred Resolution” change mentioned here Display resolution in Windows Server 2016 (AHV-VM) stuck to 1280x1024 | Nutanix Community I change the Preferred resolution from “<Unset>” to “1920x1080”, but as soon as I exit and boot into Windows, it goes back to 1280x1024 and won’t change. Some posts mention not having Guest Tools installed before the MOVE, but that made no difference for us. I’m stuck at the same resolution, regardless of whether Guest Tools was installed prior to MOVE or not. Nor does the method of access - launch console or RDP, the VM resolution is hard coded to this annoyingly small (by 21st century standards) resolution. And all my VMs are UEFI, which is pretty much the default. And obviously that can’t be changed, without deleting the whole VM. Is there any workaround or resolution (s

2011
M
A
AdamNTXVoyager
asked in Installation & Configuration
Updating tools results in hanging at uefi upon reboot. Has to be power cycled to then boot to Windows Server

SCSI disk 100gb, 16gb mem, Server 2016 standard desktop experience, dual xeon icelake Likely other configurations, as this has happened with multiple VMs, still collecting data, but wanted to get something started in case others have experience with this. My first thought is obviously some uefi configuration with boot order or something, but doesn’t really make sense, since it only *seems to happen* right after tool updates. *updated as it’s not like we reboot often, maybe it will happen without updating as well.

301
A
H
HaroonAdventurer
asked in Installation & Configuration
How to install Nutanix CE 2.1 in Dell server T350

Dear Team, I have Dell server T350 with 3 HDD of 2TB and 32GB of memory and 4 Core server. I want to deploy Nutanix AHV(Hypervisor) to that server and provision some VMs for LAB. I have downloaded Nutanix CE 2.1 ISO and loaded to USB, cant move ahead of installation after disk selection. Kindly advise on this!!

18010
H
G
GuillemAdventurer
asked in Installation & Configuration
Nutanix CE Installation Issue - InstallerVM Timeout

Hello Nutanix Community, I'm trying to install Nutanix Community Edition (CE), but I'm encountering an InstallerVM timeout issue. The installation keeps retrying, and the hypervisor setup does not complete successfully. My hardware setup: 1 HDD (480GB) → Intended for data storage. 1 SSD (2.8TB) → Assigned to CVM storage. 1 USB Drive (32GB) → Used for the hypervisor installation. Issue Description: The installation starts but gets stuck with repeated messages: INFO Hypervisor installation in progress INFO InstallerVM timeout occurred, current retry 0 I have already disabled RAID and set the SATA mode to AHCI in the BIOS. The disks are correctly recognized when using lsblk and fdisk -l. I tried wiping the disks (wipefs -a and dd if=/dev/zero), but the issue persists. Troubleshooting Attempts: Checked system RAM → I have more than 32GB available. USB Boot Media → I recreated the bootable USB with a fresh Nutanix CE ISO.

2095
G
B
blanketvmAdventurer
asked in Installation & Configuration
Duplicated CVM machine?

Hello, After 3 node cluster deployment, I can see 4 CVMs. Two of them looks like the same VM but duplicated. How to fix it and remove one of them? I cannot update vs0 on the node where two CVMs are placed.AHV/CVM reboot did not help. And I cannot use acli on that node. nutanix@NTNX-b7617012-A-CVM:10.170.0.11:~$ ncli vm list Id : 00062cfc-0318-cd70-17eb-005056b90eac::7fa39b58-506c-40f9-b5b8-54146d84855e Uuid : b452d890-a399-49b3-b415-e975c489d577 Name : NTNX-b7617012-A-CVM VM IP Addresses : 10.170.0.11, 192.168.5.2, 192.168.5.254 Hypervisor Host Id : 00062cfc-0318-cd70-17eb-005056b90eac::5 Hypervisor Host Uuid : f20c4224-3d4f-4472-bb79-2e8aa0968bc5 Hypervisor Host Name : NTNX-b7617012-A Memory : 20 GiB (21,474,836,480 bytes) Virtual CPUs : 2 VDisk Count : 0 Protection Domain : Consistency Group : Id : 00062cfc-0318-cd70-17eb-005056b90eac::9aef76d3-3584-49a1-af9c-4b50c900dd9d Uuid : 1a269e5c-0aee-4af3-af21-e036ccf0e80f Name : NTNX-b7617012-A-CVM VM IP Addresses : 10.170.0.11, 192.168.5.2

955
S
M
MaarkAdventurer
asked in Installation & Configuration
Filed to start systems management device drivers.

I have been trying to install Nutanix phoenix. But everytime i try to install it i run into the same error instsvcdrv.service not being able to start. I have tryed to find the file on the system and start it without any luck. I downloade ce from here = Download Community Edition | Nutanix Community The full line says = Failed to start systems Management Device Drivers.See ‘systemctl status instsvcdrv.service’ for more details. The only other ones i found on here with the same problem was Nutanix CE fails to install | Nutanix Community

34210
M
U
UweFaberVoyager
asked in Installation & Configuration
How to find vlanid for cvm with VMware HV

Hi, i have to extend a Cluster with ESXi7 HV, and in the foundation Software i have to fill in the vlanid for the cvm. I guess this is the default vlan, so with AHV i knew the commands to find out the vlanid, but with ESXI i have no experience. So could someone tell the the comands to find out the vlanid ? Regards Uwe

442
A
W
wileyrfWayfarer
asked in Installation & Configuration
fresh install -> cvm cluster created/started, all services

I have a fresh install of CE 2.1. Single node - Intel S2600GZ (Dual E5-2650). LSI 2380 HBA. All SSD RAID10 disks. 4x1G Intel NICs. ~400G for CVM/Data. I create the single node cluster ...waited 2 hours and cluster services are still down. Thoughts? cluster status output shows: nutanix@NTNX-c3fc6bae-A-CVM:172.16.0.20:~/data/logs$ cs 2025-03-10 14:44:49,368Z INFO MainThread zookeeper_session.py:136 Using multithreaded Zookeeper client library: 1 2025-03-10 14:44:49,370Z INFO MainThread zookeeper_session.py:248 Parsed cluster id: 5826532148493501106, cluster incarnation id: 1741611593263670 2025-03-10 14:44:49,371Z INFO MainThread zookeeper_session.py:270 cluster is attempting to connect to Zookeeper, host port list zk1:9876 2025-03-10 14:44:49,388Z INFO Dummy-1 zookeeper_session.py:840 ZK session establishment complete, sessionId=0x1958025e2ec0011, negotiated timeout=20 secs 2025-03-10 14:44:49,391Z INFO MainThread cluster:3302 Executing action status on SVMs 172.16.0.20 2025-03-10 14:44

230
W
N
niclasskovAdventurer
asked in Installation & Configuration
New CE cluster stuck on creating cluster

Hi, trying to install a new CE cluster to do some testing, and after I use the cluster -s cvm1_ip_addr,cvm2_ip_addr,... create command, it just gets stuck on the image I’ve inserted. Any ideas what I’m doing wrong?

481
JeroenTielen
U
UweFaberVoyager
asked in Installation & Configuration
prism Node dsicovery failed

Hi all, we wanne expand our cluster with 2 nodes, there are connected to Network, but wenn we start in Prism the discovery, no nodes will be found. Does anyone have a list of things we need to check Regards Uwe

474
JeroenTielen

Most awesome this week!

Badges

  • Courteous
    DOHhas earned the badge Courteous
  • Approachable
    TyShawnhas earned the badge Approachable
  • Neighborly
    Tzackhas earned the badge Neighborly
  • Approachable
    Exehas earned the badge Approachable
  • Neighborly
    chaithanya_dileephas earned the badge Neighborly
Show all badges

Popular Subjects

Terms & Conditions